All Topics > Home Services > Electrical > How To Wire A Light Switch >

How To Wire A Light Switch Maryland

Sometimes it just isn't feasible to hire a professional to do a very small job, such as wiring a lig ...

Local Companies

AC&T
301-582-2700
P.O. Box 4217
Hagerstown, MD

Meyer Electrical Services, Inc.
301-593-0565
10315 Cherry Tree Lane
Silver Spring, MD

Energy Pro
240 4268876
721 Magothy Rd
Arnold, MD

Constellation NewEnergy
(610) 433-6380
100 Constellation Way
Baltimore, MD

Plus Electric Corp.
301-422-4762
3405 Rosemary Lane
Hyattsville, MD

Big D Electric
301-724-2443
302 Virginia Ave
Cumberland, MD

TriStar Electric
410-799-5791
2979 Jessup Road
Jessup, MD

Cary Electric Company
301-924-2558
15411 Baileys Lane
Silver Spring, MD

provided by: HandyHouseholdHints.com

Sometimes it just isn't feasible to hire a professional to do a very small job, such as wiring a light switch in your home. Wiring a light switch is fairly easy as long as you follow a few simple steps.

1. Step one: Connect the bare wire, or ground wire, to the electrical box and then cut the wire off about an inch past the ground screw. Connect the black wire to one screw and the white wire, which is the hot wire, to another screw on the switch. (∗This is the ONLY time that you should use the white wire for the conducting wire, or hot wire.)

2. Step two: Most light switches will have a 2 wire #14 cable coming from the light box to the switch. At the light box, you will connect the black wire on the light switch to the black wire on the light itself. You will then connect the white wire on the light switch to the black conducting wire that comes out of the breaker. When you are connecting two wires by splicing them together, you will need to use a connector, called a marret. Make sure that the splice you have completed is strong and electrically sound, just like the original conductor was. NOTE: Sometimes your light switch might not be laid out in this fashion. In other cases, there will be a feeder wire from the breaker that enters the switch box.

3. Step three: Now you will connect the ground wires like you did before. Splice the two white wires together with a marret, and connect the black wire from the breaker to one side of the switch. The other black wire that goes to the light itself will be connected to the opposite side of the switch.

4. Step four: Now, you need to connect the ground wires to the box. You can do this in one of two ways: either put one wire under the ground screw and then use a marret to splice them together or you can put each different wire under a different screw. It is just a matter of preference on this step.

5. Step five: Connect the remaining white wire from the switch to the only silver screw on the light. Connect the remaining black wire from the switch to the brass screw on the light. Make sure that you don't get these wires crossed or going to different screws.

6. Step six: replace all the covers to the light switch and you are finished. Make sure that you test the light out before considering this project complete.

WARNING: When working with electricity, it is always best to completely turn off any electrical circuits that you will be working with before you begin your work. Always follow all safety precautions and directions on the packaging of electrical products that you are working with to prevent injury.

Read full article at HandyHouseholdHints.com

Featured Local Company

AC&T

301-582-2700
P.O. Box 4217
Hagerstown, MD

Read more about How To Wire A Light Switch

- Replace a 3-Way Switch Maryland

Determine which switch is not working. You do this by turning each switch on at both locations. With the light on, go to each switch and flip switch to opposite position.

- New Switch Installation Maryland
- How to Install a Garbage Disposal Maryland
- How To Choose The Right Light Switch Maryland
- Do It Yourself New Wiring Maryland
- Do It Yourself Outdoor Wiring Maryland
- Ceiling Fan Options Maryland
- Do It Yourself Dimmer Switch Installation Maryland
- Walkway Lights Maryland
- DIY Wiring For Light Fixtures Maryland

Regional Articles

- Replace a 3-Way Switch Maryland

Determine which switch is not working. You do this by turning each switch on at both locations. With the light on, go to each switch and flip switch to opposite position.

Related Local Events

Maintenance Solutions Expo (MS Expo )
Dates: 3/16/2010 - 3/28/2010
Location: Baltimore Convention Center
Baltimore, MD
View Details

ESX - ELECTRONIC SECURITY EXPO 2009
Dates: 6/23/2009 - 6/25/2009
Location: Baltimore Convention Center
Baltimore, MD
View Details

Advertising	Food & Beverage	Nightlife
Business Services	Franchise	Online Database
Career	Health	Pets
Cars	Holidays	Real Estate Resources
Computer Hardware	Home Appliances	Retail & Consumer Services
Construction	Home Electronics	Software
Education	Home Services	Technology
Entertainment	Industrial Goods & Services	Telecommunications
Environmental	Insurance	Trade Shows
Family	Internet	Travel
Fashion	Legal	Weddings
Financial Services	Miscellaneous	World History

Advertising	Family	Home Services	Real Estate Resources
Business Services	Fashion	Industrial Goods & Services	Retail & Consumer Services
Career	Financial Services	Insurance	Software
Cars	Food & Beverage	Internet	Technology
Computer Hardware	Franchise	Legal	Telecommunications
Construction	Health	Miscellaneous	Trade Shows
Education	Holidays	Nightlife	Travel
Entertainment	Home Appliances	Online Database	Weddings
Environmental	Home Electronics	Pets	World History