How to Caulk a Bathtub Little Rock AR

Water will penetrate your bathroom walls and cause expensive damage to your valuable home unless you take precautions with your bathtub.

Local Companies

Dixie Land Home Design, LLC
501-224-4964
3506 Luwig st
Little Rock, AR
aloha hardwood flooring
501 944 1089
4028 robinwood cr.
little rock, AR
Chuck's Surplus
(501) 888-5502
4509 W Dixon Rd
Little Rock, AR
Home Depot
(501) 565-7168
11 Mabelvale Plaza Dr
Little Rock, AR
Hot Springs Hardwood Supply
(501) 767-9663
803 Mid America Blvd
Hot Springs National Park, AR
Central Rental & Supply
(870) 365-0401
202 E Crandall Ave
Harrison, AR
Hipp Lumber & Hardware Inc
(870) 251-1656
810 Heber Springs Rd
Batesville, AR
B & L Metal Sales
(870) 741-4723
3991A Coweta Falls Rd
Harrison, AR
Plyler John Home Center & Plumbing
(870) 356-3312
Glenwood, AR
Meek's-the Builder's Choice
(479) 756-2550
4446 W Sunset Ave
Springdale, AR

Provided By:

Steps

  1. Examine the joint between the bathtub and the wall. Clean all old caulk, mildew and soap scum from the edge of bathtub. Be careful not to scratch surface of tub. Wipe with denatured alcohol to clean and remove any moisture from each seam. Rubbing alcohol contains oil that leaves residue (to keep from drying out your skin) and should not be used for cleaning.
  2. Use caulk approved for bathroom surfaces. There are choices in color and price. It seems more silicone costs more. Silicone caulk for kitchen and bath has a mildew preventer built in it.
  3. Apply masking tape to both sides of where you want your new caulk bead, with the edges of the tape lining up to exactly where you want the bead of caulk to stop. This is a technique that professionals use to ensure a perfectly even-looking bead with no mess. There should be about an eighth of an inch between the two pieces of tape.
  4. Load caulk tube in caulk gun. Using a sharp knife, cut the application tip on score mark. Opening should not be so big that a bead cannot be formed. Opening should not be so small that caulk tube seems highly pressurized. Most tubes have a thin barrier inside the tube to prevent the caulk from curing. Pierce the barrier by inserting a wire, nail or pointed object inside tip.
  5. Hold caulk gun over trash and depress trigger to move caulk forward filling the tip. Caulk should flow out, not squirt or drip. Release trigger lock to relieve the light pressure inside tube.
  6. Point tip in position at seam. Tip should be slightly above surface, nearly touching. As you begin to press trigger, watch flow of caulk. With one steady motion, move caulk gun straight along seam, creating a uniform bead. Before flow stops, quickly release trigger and begin to press again as you continue to create a uniform bead the entire length of seam. Do not stop until you reach corner.
  7. Repeat for each seam, usually three walls.
  8. When you stop, remember to release the trigger lock to relieve pressure inside tube or caulk will continue to flow out.
  9. Smooth the caulk out between the pieces of masking tape, pressing it into the corner with your finger as you go along, and removing excess caulk. Keep a few paper towels at hand to wipe your finger off if you need to.
  10. Remove the masking tape before the caulk starts to skin over. The bead should look neat and even, but you may need to clean it up slightly with your finger again for a perfect finish.
  11. Caulk must cure for 24/36 hours before exposing to water and moisture.

Tips

  • Fill the tub three quarters of the way full of water to allow the tub to sag while the silicon dries for 24 hours. Otherwise the tub will sag when you get in and pull on the seam causing possible long-term cracking and breaching.
  • A sharpened flathead screwdriver works quite well for removing old caulking (be sure not to damage underlying surfaces).
  • The process is very similar to decorating a cake.
  • Bead must fill seam between wall and bathtub. Bead must contact wall and tub uniformly along entire length or leaks will occur.
  • If you do not use the entire tube of caulk, you may plug the tip with an object such as a small wooden rod and cover with plastic or tape. Caulk will keep for a short time.
  • You can smooth out the caulk with a wet finger, plastic spoon or rounded ice cube.
  • Use a small paper cup filled halfway with lukewarm water, add 2 to 3 drops dishwashing soap and stir gently with your finger to disolve. You don't want suds. Using this to wet your finger will make cleanup easier and the silicone will not want to stick to your finger.
  • Silicon caulk is very very sticky and will not come off your fingers easily. Therefore, wear latex gloves when applying silicone caulk
  • Clean up and smoothing is easily accomplished with paper towels and "Formula 409" or other similar household cleaner.
  • After removing the tape, smooth the edges that were next to the tape, ensuring that they are feathered to the surface. Otherwise, the edge will gather dirt.
  • When smoothing the caulk, start in a corner and go 1/2 to 3/4 across. Then start in the opposite corner and meet in the middle. When meeting the already smoothed section, lightly lift your smoothing device so there isn't a hump.
  • Do one wall at a time because silicone films over rather quickly.
  • A little off topic, but when you have a tiled inside corner always use caulk instead of grout. Grout will crack out and will leak in the corners, whereas caulk stays flexible when it is cured. If you have large, sanded grout joints, you can usually find colored, sanded caulk in the same custom colors as the grout, although this isn't always the best choice for tub surrounds and showers. For this application make sure you use caulk with some amount of silicone in it, or pure silicone.
  • To remove silicone from hands just rub them with a plastic bag. It makes cleanup instant and lets you use your fingers to smooth and finish caulking without worrying about stickiness.
  • Be sure to remove all traces of caulk & mildew before applying new caulk- -yes even that residue that seems like it will not come off.

Warnings

  • Exercise caution with knife and pointed objects.
  • Do not use bathtub until caulk cures. See tube for specific instructions.
  • Important Tip - Tub should be filled 3/4 full of water during caulking, this prevents any break in the seal due to increased tub weight when it is filled with water.

Article provided by wikiHow, a wiki how-to manual. Please edit this article and find author credits at the original wikiHow article on How to How to Caulk a Bathtub. All content on wikiHow can be shared under a Creative Commons license.

Featured Local Company

Dixie Land Home Design, LLC

501-224-4964
3506 Luwig st
Little Rock, AR

Related Articles
- Firestopping Products Little Rock AR
With the increasing demand for electricity, additional capacity and speed of new cabling installations, a need arose for firestop products that once were considered permanent, to become far more temporary. End users demanded all of the flexibility of a temporary firestop with all of the performance attributes of a permanent firestop.
- Recycled décor Little Rock AR
- Improper Deck Flashing Problem Little Rock AR
- Bathroom Remodeling Little Rock AR
- Colored Caulking Little Rock AR
- How to Replace a Pre Hung Door Little Rock AR
- Protect Your Log Home From Carpenter Bees Little Rock AR
- Home Improvement Links Little Rock AR
- Bathroom Fixtures Little Rock AR
- Chair Rail Installation Little Rock AR
Related Articles

Rss   Delicious   Digg   Add To My Yahoo   Add To My Google   Bookmark   Search Plugin

Topics:
Advertising Family Home Services Real Estate Resources
Business Services Fashion Industrial Goods & Services Retail & Consumer Services
Career Financial Services Insurance Software
Cars Food & Beverage Internet Technology
Computer Hardware Franchise Legal Telecommunications
Construction Health Miscellaneous Trade Shows
Education Holidays Nightlife Travel
Entertainment Home Appliances Online Database Weddings
Environmental Home Electronics Pets World History