How to Replace Drive Belt on the Kenmore Dryer Model Series 60301 to 70301 Maine

This article is about how to replace a dryer drum belt on a Kenmore Dryer, Model Series 60301 to 70301. If you own one of these dryers and are having problems with it, read on for helpful advice on how to fix it.

Local Companies

Maddabout Coffee
207 5101823
19 Industrial Park Road
Saco, ME
Downeast Appliance
(207) 772-0053
845 Forest Ave
Portland, ME
Bailey's Appliance Repair Inc
(207) 929-4495
204 Portland Rd
Buxton, ME
Jim's Appliance Service
(207) 633-6161
Edgecomb, ME
Cole Appliance Service
(207) 883-5816
PO Box 301
Scarborough, ME
Jim's Appliance Service
(207) 563-1693
Damariscotta, ME
Jim's Appliance Service
(207) 798-7901
Bradford Rd
Wiscasset, ME

Provided By:

Steps

  1. MOST IMPORTANT: Make sure you have the power plug unplugged.
  2. Now, from the front side facing you, insert a screwdriver between the lid and front panel. You will find there are two pop-in holders; each one is approximately 3 inches from each side. Pop the lid. (don't for get the remove the lent trap and the two screws under it.)
  3. Lift the lid all the way up so it is out of the way. Now, very gently lower the whole dryer onto its back side. (The lid will stand on its own.)
  4. Then, on the inside of the front panel you will find two screws holding the front panel on. Remove these screws. Now the front panel can be removed. Use caution when you remove the front panel, as the drum will now be loose and will tip downwards. You can remove the drum if you'd like to have complete access to the motor and clean out the insides. (Un Connect the two wires to the door sensor)
  5. Locate the broken belt and remove it.
  6. Locate the belt tension bracket. (It has a plastic roller attached.) If it is out of position, note the holes in bottom in front of the motor. With the plastic roller facing the drum, insert the belt tension bracket.
  7. Place new belt around the drum, and try to locate it in same place that the old belt ran. Make sure you place the groove side down on the drum.
  8. Once the belt is in place, insert it underneath the plastic roller and lift up on the belt tension bracket until you can loop the end around the motor spindle.
  9. Now replace the front panel, making sure you align the door opening properly on to the drum front. Replace the two screws holding the front panel to the cabinet.
  10. Now lift the dryer back upright, and secure the lid back to front panel.
  11. Replug in dryer and you have finished the job.
  12. The belt for this model, Part number is 341241, can be purchased from a Whirlpool supplier.

Things You'll Need

  • Screwdriver
  • Replacement drive belt

Article provided by wikiHow, a wiki how-to manual. Please edit this article and find author credits at the original wikiHow article on How to How to Replace Drive Belt on the Kenmore Dryer Model Series 60301 to 70301. All content on wikiHow can be shared under a Creative Commons license.

Featured Local Company

Maddabout Coffee

Through a transparent coffee chain we begin to educate our customers on responsible purchasing.

207 5101823
19 Industrial Park Road
Saco, ME
www.maddaboutcoffee.com/responsibility.php

Maddabout Coffee is a wholesale specialty coffee roaster, with emphasis on providing socially and environmentally superior coffee, and educating customers about the social and environmental issues surrounding coffee production to encourage customer decisions which are better for our planet.

Responsible Coffee

Related Articles
- How to Repair the Motor Coupler in a Kenmore Washer Maine
If your washing machine's motor is running but the washer fails to spin or agitate, the problem is very likely with the motor coupler, which connects the motor and the gearcase. Note: some washers, especially those made before 1985, are belt drive, in which case none of the following applies.
- How to Replace a Broken Drive Belt in a Clothes Dryer Maine
- Setting Up a Washer and Dryer Maine
- How to Repair Loose Baffles in Your Dryer Tumbler Maine
- Washer Dryer Hookup Installation Maine
- How to Change the Heating Element in a Dryer Maine
- How to Keep Lint off Clothes in the Dryer Maine
- Dryer Maine
- How To Replace Drive Belt On Tumble Dryer Maine
- How to Replace the Evaporator Fan in a Kenmore Refrigerator Model 106 8627580 Maine
Related Articles
- How to Repair the Motor Coupler in a Kenmore Washer Maine
If your washing machine's motor is running but the washer fails to spin or agitate, the problem is very likely with the motor coupler, which connects the motor and the gearcase. Note: some washers, especially those made before 1985, are belt drive, in which case none of the following applies.
- How to Replace a Broken Drive Belt in a Clothes Dryer Maine
- Setting Up a Washer and Dryer Maine
- How to Repair Loose Baffles in Your Dryer Tumbler Maine
- Washer Dryer Hookup Installation Maine
- How to Change the Heating Element in a Dryer Maine
- How to Keep Lint off Clothes in the Dryer Maine
- Dryer Maine
- How To Replace Drive Belt On Tumble Dryer Maine
- How to Replace the Evaporator Fan in a Kenmore Refrigerator Model 106 8627580 Maine

Rss   Delicious   Digg   Add To My Yahoo   Add To My Google   Bookmark   Search Plugin

Topics:
Advertising Family Home Services Real Estate Resources
Business Services Fashion Industrial Goods & Services Retail & Consumer Services
Career Financial Services Insurance Software
Cars Food & Beverage Internet Technology
Computer Hardware Franchise Legal Telecommunications
Construction Health Miscellaneous Trade Shows
Education Holidays Nightlife Travel
Entertainment Home Appliances Online Database Weddings
Environmental Home Electronics Pets World History