All Topics > Home Appliances > How to Replace Drive Belt on the Kenmore Dryer Model Series 60301 to 70301 >

How to Replace Drive Belt on the Kenmore Dryer Model Series 60301 to 70301 North Carolina

This article is about how to replace a dryer drum belt on a Kenmore Dryer, Model Series 60301 to 70301. If you own one of these dryers and are having problems with it, read on for helpful advice on how to fix it.

Local Companies

Appliancetech Inc
(704) 643-7763
1400 Sharon Rd W
Charlotte, NC

Air Makers
(919) 878-8800
5420 Old Poole Rd
Raleigh, NC

Appliance World
(919) 571-1803
5910-125 Duraleigh Rd
Raleigh, NC

Kitchen & Bath Galleries
(919) 783-7100
8411 Glenwood Ave
Raleigh, NC

AC Corporation
(919) 782-0896
3200 Glenwood Ave
Raleigh, NC

A Plus Appliance Service and Installation
704-829-7734
4918 S. New Hope Rd.
Belmont, NC

Wooten Refrigeration
(336) 909-2126
395 Warp Drive
Cleveland, NC

A C Heating Experts
(919) 779-2736
2817 Buckboard Ln
Raleigh, NC

Reliable Appliance
(704) 864-5281
1911 E. Ozark Avenue
Gastonia, NC

Provided By:

Steps

MOST IMPORTANT: Make sure you have the power plug unplugged.
Now, from the front side facing you, insert a screwdriver between the lid and front panel. You will find there are two pop-in holders; each one is approximately 3 inches from each side. Pop the lid. (don't for get the remove the lent trap and the two screws under it.)
Lift the lid all the way up so it is out of the way. Now, very gently lower the whole dryer onto its back side. (The lid will stand on its own.)
Then, on the inside of the front panel you will find two screws holding the front panel on. Remove these screws. Now the front panel can be removed. Use caution when you remove the front panel, as the drum will now be loose and will tip downwards. You can remove the drum if you'd like to have complete access to the motor and clean out the insides. (Un Connect the two wires to the door sensor)
Locate the broken belt and remove it.
Locate the belt tension bracket. (It has a plastic roller attached.) If it is out of position, note the holes in bottom in front of the motor. With the plastic roller facing the drum, insert the belt tension bracket.
Place new belt around the drum, and try to locate it in same place that the old belt ran. Make sure you place the groove side down on the drum.
Once the belt is in place, insert it underneath the plastic roller and lift up on the belt tension bracket until you can loop the end around the motor spindle.
Now replace the front panel, making sure you align the door opening properly on to the drum front. Replace the two screws holding the front panel to the cabinet.
Now lift the dryer back upright, and secure the lid back to front panel.
Replug in dryer and you have finished the job.
The belt for this model, Part number is 341241, can be purchased from a Whirlpool supplier.

Things You'll Need

Screwdriver
Replacement drive belt

Article provided by wikiHow, a wiki how-to manual. Please edit this article and find author credits at the original wikiHow article on How to How to Replace Drive Belt on the Kenmore Dryer Model Series 60301 to 70301. All content on wikiHow can be shared under a Creative Commons license.

Featured Local Company

Appliancetech Inc

(704) 643-7763
1400 Sharon Rd W
Charlotte, NC

Read more about How to Replace Drive Belt on the Kenmore Dryer Model Series 60301 to 70301

- How To Replace Drive Belt On Tumble Dryer North Carolina

Here's how to replace a drive belt on Creda tumble dryer. If you have any difficulty getting the belt over the drum, remove the outer screws on the back cover, leaving the ground level ones in place.

- How to Replace the Evaporator Fan in a Kenmore Refrigerator Model 106 8627580 North Carolina
- How to Keep Lint off Clothes in the Dryer North Carolina
- Setting Up a Washer and Dryer North Carolina
- Washer Dryer Hookup Installation North Carolina
- How to Change the Heating Element in a Dryer North Carolina
- How to Replace a Broken Drive Belt in a Clothes Dryer North Carolina
- How to Repair the Motor Coupler in a Kenmore Washer North Carolina
- How to Repair Loose Baffles in Your Dryer Tumbler North Carolina
- Dryer North Carolina

Regional Articles

- How To Replace Drive Belt On Tumble Dryer North Carolina

Here's how to replace a drive belt on Creda tumble dryer. If you have any difficulty getting the belt over the drum, remove the outer screws on the back cover, leaving the ground level ones in place.

Related Local Event

From Shredding to Background Checks: Protecting Your Customers, NorthWest Chapter Breakfast
Dates: 11/19/2009 - 11/19/2009
Location: Pine Island Country Club
Charlotte, NC
View Details

Advertising	Food & Beverage	Nightlife
Business Services	Franchise	Online Database
Career	Health	Pets
Cars	Holidays	Real Estate Resources
Computer Hardware	Home Appliances	Retail & Consumer Services
Construction	Home Electronics	Software
Education	Home Services	Technology
Entertainment	Industrial Goods & Services	Telecommunications
Environmental	Insurance	Trade Shows
Family	Internet	Travel
Fashion	Legal	Weddings
Financial Services	Miscellaneous	World History

Advertising	Family	Home Services	Real Estate Resources
Business Services	Fashion	Industrial Goods & Services	Retail & Consumer Services
Career	Financial Services	Insurance	Software
Cars	Food & Beverage	Internet	Technology
Computer Hardware	Franchise	Legal	Telecommunications
Construction	Health	Miscellaneous	Trade Shows
Education	Holidays	Nightlife	Travel
Entertainment	Home Appliances	Online Database	Weddings
Environmental	Home Electronics	Pets	World History